Bar ends for the 310 - BMW G310 R/GS Forum
 4Likes
Reply
 
LinkBack Thread Tools
post #1 of 24 (permalink) Old 11-07-2017, 12:17 AM Thread Starter
Super Moderator
 
porth's Avatar
 
Join Date: May 2017
Location: Brisbane Australia
Posts: 738
Garage
Bar ends for the 310

Puig make bar ends for the 310 (part number 8804), Barracuda also make bar ends (part number bt1000)


Anyone know of any other bar ends that will fit the 310?
Nickharo likes this.
porth is online now  
Sponsored Links
Advertisement
 
post #2 of 24 (permalink) Old 11-07-2017, 08:10 AM
Senior Member
 
Tactical_r3dn3ck's Avatar
 
Join Date: Sep 2017
Posts: 340
I think most bar ends that will fit 7/8" bars will work.
Nickharo likes this.
Tactical_r3dn3ck is offline  
post #3 of 24 (permalink) Old 11-15-2017, 07:02 AM
Junior Member
 
TrentAJ's Avatar
 
Join Date: Nov 2017
Posts: 29
Garage
I ordered a set of R&G Bar Ends from Twisted Throttle that are specifically for the G310R.
Nickharo likes this.
TrentAJ is offline  
post #4 of 24 (permalink) Old 11-15-2017, 03:18 PM Thread Starter
Super Moderator
 
porth's Avatar
 
Join Date: May 2017
Location: Brisbane Australia
Posts: 738
Garage
Bar ends with an M8 threaded bolt should work, otherwise get yourself a thread adapter (e.g. M6 to M8, M12 to M8)
porth is online now  
post #5 of 24 (permalink) Old 11-15-2017, 04:05 PM
Senior Member
 
Tactical_r3dn3ck's Avatar
 
Join Date: Sep 2017
Posts: 340
I just took my throttle side bar end off to repaint it from when it fell over. The bar end it's self isn't threaded only the end of the handle bar.
Tactical_r3dn3ck is offline  
post #6 of 24 (permalink) Old 12-12-2017, 01:05 AM Thread Starter
Super Moderator
 
porth's Avatar
 
Join Date: May 2017
Location: Brisbane Australia
Posts: 738
Garage
Anyone know how to get the threaded inserts out of and back into the handlebar?


Just bought Rizoma bar ends MA534 in silver. I assume they come with M6? socket screws, so the options that I have as I see it are:
1. Remove threaded inserts.
2. Get thread adapters M8 to M6?.
3. Get M8 socket screws and drill 8mm hole into the bar ends.

Last edited by porth; 12-12-2017 at 01:10 AM.
porth is online now  
post #7 of 24 (permalink) Old 12-12-2017, 06:42 AM
Senior Member
 
Tickster's Avatar
 
Join Date: Nov 2017
Location: Leduc Alberta Canada
Posts: 469
Well mine came out on the throttle side while trying remove the OEM bar end.
Left side stayed in.
I had a tough time removing the bolts and the whole insert had to come out for me to get
the bolt out of it.
Thread the bolt back in minus the bar end and tighten enough to loosen up the insert,
back the bolt up a bit and pull.
It will come out with some effort.
Good luck.

2018 Black 310GS
2011 Royal Enfield Classic with Cozy Bullet sidecar
1981 Honda 400 Homemade Bobber
1978 Honda Naked Goldwing
16 past varieties too numerous to mention
Tickster is offline  
post #8 of 24 (permalink) Old 12-12-2017, 07:58 PM Thread Starter
Super Moderator
 
porth's Avatar
 
Join Date: May 2017
Location: Brisbane Australia
Posts: 738
Garage
Thanks, so threading the screw in that extra distance causes the insert to loosen (I assume by causing part of the insert to move inwardly)?


Do you have a picture of the insert?
porth is online now  
post #9 of 24 (permalink) Old 12-13-2017, 07:11 AM
Senior Member
 
Tickster's Avatar
 
Join Date: Nov 2017
Location: Leduc Alberta Canada
Posts: 469
Quote:
Originally Posted by porth View Post
Thanks, so threading the screw in that extra distance causes the insert to loosen (I assume by causing part of the insert to move inwardly)?


Do you have a picture of the insert?
When fully threaded in, and you tighten it up it should then rotate the
insert to loosen up its death grip on the bar.
Then pull hard and both should slide out, helps if you continue to
turn the bolt while pulling.

Will try to get a picture for you soon.

2018 Black 310GS
2011 Royal Enfield Classic with Cozy Bullet sidecar
1981 Honda 400 Homemade Bobber
1978 Honda Naked Goldwing
16 past varieties too numerous to mention
Tickster is offline  
post #10 of 24 (permalink) Old 12-13-2017, 05:57 PM Thread Starter
Super Moderator
 
porth's Avatar
 
Join Date: May 2017
Location: Brisbane Australia
Posts: 738
Garage
Ok, thanks, I understand that. I'll try it.
porth is online now  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome